石墨增碳剂介绍：

    增碳剂是炼钢时用的一种添加剂。它是生产钢材较合适的原料。另外，也是生产电糊的原料。

    增碳剂的原料有很多种，生产工艺也各异，有木质碳类，煤质碳类，焦炭类，石墨类等。石墨化的增碳剂，在高温条件下，碳原子的排列呈石墨的微观形态，所以称之为石墨化。石墨化可以降低增碳剂中杂质的含量，提高增碳剂的碳含量，降低硫含量。

石墨增碳剂特点：

    1、高固定碳，吸收率高，低硫低氮，并在吸收速度上快于同类石墨化增碳剂，且不吸附炉壁， 吸收无残留，价格低于同类硫低于0.05以下的石墨化增碳剂，性价比高。

    2、吸收率高, 根据使用方法吸收率能达到90以上.。

    3、吸收速度快,比 同类石墨化增碳剂吸收速度快，不吸附炉壁，且无残留，炉中增碳吸收速度优势更加明显。

    4、硫份低， 0.05以下，低至0.02。氮份低，100ppm以下。

    5、超高的性价比，综述上述在同类石墨化增碳剂中（硫0.05）价格较有优势。 

    6、效益影响：石墨增碳剂为您降低成本，提高产品质量。

    7、原材料可增加废钢用量，减少生铁用量或不用生铁，有效避免生铁的遗传性对铸件的影响。 

    8、含硫低，稳定可靠，有效节约硫在球化和孕育过程中对合金的不利影响，节省合金费用。 

    9、由于熔点低，吸收快，不反渣，可以有效保护和延长炉龄，减少炉衬消耗。

    10、化学成分纯净：高碳、低硫、微氮，杂质少 。

    11、物理形态：外观洁净、无杂质，多孔隙结构，吸收速度快，吸收率高 。

    12、微观形态：晶体度质量优，有效提升铸件铸铁牌号和性能 。     

    13、产品性质稳定：增碳效果稳定，吸收效果好，提温效果明显，不返渣。

石墨增碳剂理化指标：

石墨增碳剂在电炉内的使用方法：

    1、电炉底部放置炉料三分之一后，将计算好的本产品放置炉料上，然后把剩余炉料按要求放在上面，如上面的炉料较大时应把一些碎的炉料压在增碳剂上，以防止漂浮影响吸收率。

    2、加料顺序少量铁削、增碳剂、废钢、回炉料。基本上增碳剂吸收量为90以上，比较高可以达到95,升温达到1560°扒渣出炉即可。炉内铁水不要出完，预留部分铁水，然后加增碳剂，再加铁屑、废钢等，增碳剂直接加到炉底，会对增碳剂的烧损过大，在炉底预留一部分铁水加入更好些，或者炉底放一部分铁硝也可以，那样吸收更高一些。

增碳剂包装：

    增碳剂包装采用防水编织袋25KG/袋，外加吨袋或托盘，也可根据您的需要提供合适包装。产品应存放在清洁、干燥的库房内，防止受潮和沾污。

厂   名：平泉县兰天活性炭厂

地   址：中国 河北 平泉县 平泉镇红花沟村
刘敏
手   机：
Q    Q：2259151836
邮   箱：2259151836@OO.com
网   址：*

The graphite carburant:
Carburant is an additive used in steelmaking. It is essential to producing high quality steel material. In addition, but also the production of electrode paste materials.
Recarburizer there are many kinds of raw materials, the production process is different, the woodiness carbon, coal carbon, coke, graphite etc.. High quality carburizing agent generally refers to after graphite carburant, in under the condition of high temperature and carbon atoms arranged in graphite morphology, so called for graphitization. Graphite can reduce the content of impurities in the carburant carburant, increasing carbon content, reducing sulfur content.
Graphite carburant characteristics:
1, high fixed carbon, high absorption rate, low sulfur, low nitrogen and in the absorption speed faster than similar graphite carburant, and adsorption of furnace wall, fully absorb the residue free, the price is lower than the similar sulfur is less than 0.05 following the graphitized carbon agent, the highest price.
2, high absorption rate, according to the use of the method to achieve the highest absorption rate can reach more than 90.
3 absorption speed, faster than similar graphite carburant absorption rate, adsorption of furnace wall and no residue, furnace carbon absorption speed advantage is more obvious.
4, sulfur share is low, below 0.05, the lowest 0.02. Low nitrogen, 100ppm.
5, the high cost, in the review of similar graphitization recarburizer (sulfur in less than 0.05) the optimal price advantage.
6 Effects: graphite carbon agent for you to reduce costs, improve product quality.
7, raw materials can increase the amount of scrap and reduce the amount of pig iron or no iron, effectively avoid the pig genetic influence on the casting.
8, low sulfur, stable and reliable, effective conservation of sulfur in the process of the ball and inoculation of the adverse effects of the alloy, saving alloy costs.
9, because of low melting point, fast absorption, not anti slag, can effectively protect and extend the furnace to reduce the consumption lining.
10, pure chemical composition: carbon, sulfur, nitrogen, less impurity.
11, physical form: the appearance of clean, free of impurities, porous structure, quick absorption, high absorption rate.
12, micro morphology, crystal degree quality, improve grades and performance of cast iron castings.
13, the product quality is stable, carbon stable effect, good absorption effect, temperature effect, do not return slag.
Using the method of graphite carburant in electric furnace:
1, furnace bottom place after one third of the charge will be calculated and the products placed in charge, then the remaining charge according to the requirements in the above, such as the above charge large should put some of the crushing burden of pressure on the carburant, to prevent the floating effect absorption rate.
2 and the sequence of adding a small amount of iron chipping, carburetant, scrap steel, scrap. Basically carburetant absorption amount is more than 90, can reach 95 of the maximum temperature reached 1560 degrees, the slag can be released.
Furnace molten iron not finished, set aside part of the hot metal, and then add the carburant, coupled with scrap iron and scrap steel etc., carburizing agent is applied directly to the bottom, burning loss of the carburant is too large, in the bottom set aside a part of molten iron is added better, or bottom placed a portion of the iron nitrate can also, so absorbed higher.

contact information：
Factory name: Pingquan County Lantian Activated Carbon Factory
Address: China Pingquan Hebei Pingquan County town of safflower Village
Contact: Liu Min
Hand machine:
Q Q:2259151836
Mail box: 2259151836@OO.com
Website: *

厂   名：平泉县兰天活性炭厂

地   址：中国 河北 平泉县 平泉镇红花沟村

刘敏
手   机：
Q    Q：2259151836
邮   箱：2259151836@OO.com
网   址：*