【电镀表面金属油墨、上海供应金属电镀丝印油墨商】价格_批发_厂家_参数_图片_印铁油墨

1/1

电镀表面金属油墨、上海供应金属电镀丝印油墨商

¥240.00

1-4罐

¥220.00

5-9罐

¥200.00

≥10罐

产品规格

颜色: 40 调色

上海凯贤印刷科技有限公司

16年

经营年限

上海

所在地区

4.5

综合评分

全部产品进入店铺

图文详情

产品属性

]UO6JF[)ESC(SL)${LZEYO3.jpg G}89NA(C[P}~(IX%}8_LSOS.jpg 34DU)0XE$K{9LK2W8{%LUTN.jpg QQ图片21.jpg QQ图片25.jpg

欧莱斯MPE电镀油墨

主要用于电镀表面、强化表面、真空电镀表面．PU表面．UV表面等材料上，具有高色泽、高色彩、高遮盖力、高稳定性、耐酒精及耐磨擦之特点。

印刷：丝印移印均可。

表干及实干时间：表干时间自然挥发5-10分钟；实干时间在24小时以内。

稀释及清洗：SV3慢干开油水、UVK1（移印开油水）同时可使用718洗网水清洗。

测试方法（完全干燥后）：

1、3m胶纸粘在画有百格的油墨表面，45度角迅速拉起不脱油;

2、纯度99的工业酒精，一千克砝码用棉布包住在油墨表面，以水平力来回拉200次无脱色;

3、耐磨：橡皮擦500g力水平来回擦500次。

使用方法：

1、使用前应充分搅拌，用后随时封闭；

2、搅拌时加开油水10-15，稀释到印刷粘度；

3、网板塞网时可用洗网水清洗；

4、不得与其它类型油墨混合使用。

注意事项：

1、塑胶材料的外观相似，但可能会是不同的材料，客户需试印确定其符合要求后，再批量印刷；

2、在移印过程中，如出现拉丝或散开，可适当加入一些慢干膏即可;

3、环境温度过高，将会影响油墨原有质量；

4、根据气候变化，请远离火源，阴暗环境下存放。

MPE plating strengthening series ink characteristics : mainly used in plating surface, enhanced surface, vacuum plating surface.PU surface.UV surface and other materials, with a high color, high color, high covering power, high stability, high alcohol and rub characteristics. Printing: screen printing can be. Surface drying and drying time: surface dry time natural volatile 5-10 minutes; work time within 24 hours. Dilution and cleaning: SV3 slow dry open water, UVK1 ( printing open water) can be simultaneously used 718 washing network water cleaning. Test method ( completely dry ): 1, 3M gummed paper in the paintings of the surface of the ink, 45 degree angle quickly pulled off the oil; 2, 99 of the purity of industrial alcohol, one kilogram of weight of cotton pack in the ink surface, with a horizontal force pulling back and forth 200 times without decolorization; 3: oak, wear resistance eraser 500g force level brush back and forth 500 times. Usage: 1, use should be fully stirred, use at any time after the closure; 2, add water mixing 10-15, diluted to 3, screen printing viscosity; the plug is available when washing network water cleaning; 4, not with other types of ink mixing. Note: 1, the plastic material similar in appearance, but may be of different materials, customers need to try to determine its requirements, and then batch printing; 2, in the printing process, such as drawing or spread out, may be appropriate to add some slow dry plaster; 3, the ambient temperature is too high, will affect the quality of the original ink; 4, according to climate change, please stay away from fire, dark environment storage.

QQ图片22.jpg QQ图片25.jpg QQ图片24.jpg QQ图片29.jpg QQ图片21.jpg