- 产品
- 详情
- 推荐
收藏
¥0.18
600-4999PCS
¥0.16
5000-9999PCS
¥0.14
≥10000PCS

产品规格
可售数量: 100000PCS
3GT系列(慢断)保险丝规格书
1. 适用范围:
本产品慢断微型玻璃管保险丝,适用于各类在250V以下电压电子电器元件内的电路中起过电流保护作用
The fuse is aTime-Lag microglass fuse , for the electronic device which rated voltageis less than AC 250V.
:p>
2. 形状,外观及尺寸如下图(单位:mm)
The out view, construction and dimensions to the following figure.(Unit:mm)
3.产品标志(Marking)
3.1 保险丝上的标志应易于看清。
The relevant markings shall be marked on the caps of the fuse and shall be easily visible.
3.2保险丝上必须有下列标示:
The markings for every fuse shall be prescribed as below according to the types.1)
安规认证标示(SafetyApprovalLogo):
2) 额定电流(Rated Current):3.15A
3) 额定电压(Rated Voltage):250V
4) 商标(Trademark):
5) 特性符号(Characteristic symbol):T
注意:本产品对标示的大小和位置没有规定
Note:This product to sign the size and position of no provisions
4.外观与形状(Appearance and shape)
4.1外观(Shape)
外观不应有显着的污点,铁锈或裂纹且标示应很容易辨认的.
Appearance should not stain, rust or cracks and marked should be easily recognizable
4.2形状(Appearance)
微型保险丝(Micro Fuse)
5.机械特性(Mechanical properties)
5.1 拉力强度实验(Tensile strength Test)
将保险丝固定好后,对保险丝两端引线施加5N的轴向拉力,持续一分钟,实验过后保险丝没有任何破损现象.
Will fuse fixed good after,Fuse on both ends of the lead5 N axial tensile force for a minute, the experiment without any damage after the fuse phenomenon
5.2 推力实验(Thrust Test)
将保险丝固定好后,轴向施加2N的推力,持续10秒钟,实验过后,保险丝没有任何破损.
Fuse holder, axial impose 2N thrust for 10 seconds after the experiment, the fuse without any damage
5.3 弯曲强度实验(注:此条只针对带引线保险丝)
Flexural strength Test(Note: this only with a lead fuse)
施加5N引线弯折90度往返一次弯折,实验过后不发生损坏
Imposed the 5N leads bent 90°and from the first bending experiment after the damage occurred
6.电气特性(ElectricalCharacteristic)
6.1实验条件(TestCondition)
所有测试环境温度25+5,测试期间室内温度变化不得超过5
All the test environment temperature of 25 +5
during the test the indoor temperature must not exceed 56.2 负载能力(LoadCapacity)
在通过150的额定电流1小时保险丝不能熔断,通电实验中保险丝连接处不能融化,保险丝外壳不能有烧焦,破裂现象.
Acurrent150
Rated Current is then passed through the fuse-link for1hour, Power experiments, the fuse junction can not melt, fuse housing can not be burnt, rupture phenomenon.6.3平均I-T特性曲线图(供参考)
TheAVERAGE I-t Characteristics Curve(For referenge only)
7. 电压降(Voltage Drop)
熔断体在额定电流条件下,两端的电压降不应超过下表规定的 值。
The voltage drop across the fuse-link at their rated current shall not exceed the maximum values is in follows.
8. 温度上升(TemperatureRise)
在150额定电流条件下,通电15min后,将电流以每15min增加10,直到保险丝断线,保险丝各部位温度不超过135
Power after 15min in 150 of rated current conditions, the current per 15min 10, until the fuse blows, the fuse various parts of the temperature does not exceed 135
9.耐久性试验/ ENDURANCE TEST
耐久性试验过程(The process of endurance test is as follows.)
1)对熔断体通过1倍的额定电流1小时,然后切断电流15分钟,重复此循环100 次。
current 1.0In is passed through the fuse-link for a period of 1hour. The current is then switched off for a period of 15 minutes. The cycle is repeated 100 times.
2)然后对熔断体通以1.5倍额定电流1小时;并测量两端电压降,计算其 功耗不能超过上表所规定的 值。
Fuse through to 1.5 times the rated current of 1 hour; and measure the voltage drop across, to calculate the maximum power consumption can not exceed the above table under the maximum
3) 测量熔断体两端的电压降,且电压降的增大量不大于试验前测得值的10。
Measuring both ends of the fuse voltage drop, and a large number of the increased voltage drop is not greater than 10 of the measured value before the test.
4) 试验后,标记仍应清晰可辨,而且诸如端帽上的焊点不应出现任何明显的劣变。
After the test, the marking shall still be legible and soldered joints on end caps, for example, shall not show and appreciable deterioration.
10.分断能力(Breaking Capacity)
35A或10In 250V AC条件下,保险丝分断电路后,保险丝管不应破裂、铜帽飞脱、且铜帽两端的绝缘电阻不小于0.1MΩ
The breaking capacity should reach the breaking rated current given in the following table at 35A or 10In 250V AC. And after this test, there should be no damage of the fuse-tube or shattering of the caps. After this test, the insulation resistance between the end caps shall be not less than0.1MΩ.
11. 焊接参数(Soldering Parameters)
1) 波峰焊接( Wave soldering): 260, 10sec. Max..
2) 手工焊接(Manual soldering): 300, 3sec. Max..
12.保存条件
温度(Temperature): +1060
湿度(Humidity):相对温度75下平均可以存放3年
Average relative temperature 75 can be stored for 3 years
在非露天的情况下,相对湿度为95, 多可存放30天.
In the case of non-open, the relative humidity of 95, can store up to 30 days
13. 包装要求(Packing Details)
13.1包装方式(Packing Mode)
1) 500个/小袋或200/小袋
500pcs/little plastic-bag or 200pcs/little plastic-bag
2) 4小袋/小盒或10小袋/小盒
4 little plastic-bags/little box
3) 10小盒/大盒
10 littleboxes/big box
13.2所有产品的包装应能达到防潮、抗振的作用,以防在运输或贮存过程中产品受潮或损坏
Packing should meet the requirements of anti-moisture and anti-shaking so that the products will not absorb moisture or be damaged during transportation or storage.


厂家直销 弯角成型 防爆 过雷击玻璃管 陶瓷保险丝 玻璃保险丝 认证齐全3.6/10 5/20 6/30 0.2A-30
¥ 0.14 ~ ¥ 0.18
¥0.14
100000PCS可售

询价单发送成功~