【上海荣计达JSF-550砂磨搅拌分散机】价格_批发_厂家_参数_图片_其他仪器仪表

1/1

上海荣计达JSF-550砂磨搅拌分散机

¥ 3800.00

1台起订

产品规格

可售数量： 100台

上海荣计达仪器科技有限公司

采通通 6 年实名企业

10年

经营年限

上海

所在地区

10.0

综合评分

全部产品进入店铺

图文详情

产品属性

一、产品简介：

该产品保持了搅拌、砂磨、分散多种的功能于一体的优点。电机采用了变频鼠笼电机、无电刷、使用寿命长，噪音更低，适合在实验室里使用。为了便于操作，变频器直接安装在机器上。变频器的显示屏直接显示转轴转速。是采用国外新技术新产品，该产品集中了搅拌、砂磨、分散多种设备的功能于一体，采用变频无极调速，变频器显示屏直接显示转轴转速。
Product introduction:

二，This product maintains the advantages of mixing, sanding and dispersing multiple functions. The motor uses a variable frequency squirrel cage motor, has no brushes, has a long service life and lower noise, and is suitable for use in the laboratory. For easy operation, the inverter is installed directly on the machine. The display of the frequency converter directly displays the shaft speed. It adopts new foreign technology and new products. This product integrates the functions of mixing, sanding and dispersing a variety of equipments. It adopts frequency conversion stepless speed regulation, and the display screen of the frequency converter directly displays the rotation speed of the shaft.

二、技术参数：
♦电机功率：550W。
♦变频器：750W。
♦输入电源：220V，50Hz。
♦调速范围：0～10000r/min（无级调速）。
♦分散叶片直径：Ø50mm，Ø60mm。
♦砂磨盘直径：Ø50mm，Ø60mm。
♦升降行程：280mm。
♦料桶容积：1.3升（双层、可冷却）。

♦外形尺寸：450X420X550mm

♦重量：40kg
Technical parameters:

♦ Motor power: 550W.

♦ Frequency converter: 750W.

♦ Input power: 220V, 50Hz.

♦ Speed regulation range: 0 ～ 10000r / min (stepless speed regulation).

♦ Dispersion blade diameter: Ø50mm, Ø60mm.

♦ Sand grinding disc diameter: Ø50mm, Ø60mm.

♦ Lifting stroke: 280mm.

♦ Capacity: 1.3 liters (double-layer, coolable).

♦ Dimensions: 450X420X550mm

♦ Weight: 40kg

三、操作规程：
开车前
♦检查分散机油位是否加注到规定位置，低应加至规定油位，高应放至规定位置。
♦检查三角皮带松紧是否适当。
♦用手盘动叶轮应转动灵活，无磨擦声。
♦检查各紧固件是否松动及各密封部位有无渗漏现象。
♦开启分散机主电机，检查搅拌的旋向是否与设备所规定的方向相同。
♦确认以上检查工作无误后方可开车。
开车
♦将叶轮放在分散机容器的中心位置，揿下降按钮，下降到低位置或要求的位置。
♦两只手柄必须锁紧后才能开车。
♦开主电机，按操作需要转速按下按钮，
♦操作过程中应经常注意电流，如发现超载运转，应停车检查原因，采取措施后再继续运转分散机。
停车
♦先停主电动机，使叶轮全部停止转动。
♦开分散机上升按钮，使主轴叶轮上升至容器之上，清洗叶轮。
电源条件：
♦电源电压波动通常交流选用 %10%、-15%，直流允许±%10左右，如若超差，须采取稳压措施或提出特殊订货要求。
♦应根据电源容量选择额定电流和消耗功率。须注意交流起动时VA值较高，在容量不足时应优先选用间接导式分散机。
♦根据供电电源种类，分别选用交流和直流分散机。一般来说交流电源取用方便。
♦电压规格用尽量优先选用AC380V、AC220V 、DC24V。

四、标准配置：
♦主机一台（含变频调速器）
♦不锈钢分散盘 2个：直径50mm,60mm各一个
♦尼龙研磨盘：2个：直径50mm，60mm各一个
♦不锈钢夹层料筒1.2L一个
♦夹持手柄2个
Third, the operating procedures:

Before driving

♦ Check whether the oil level of the dispersing machine is filled to the specified position, the low level should be added to the specified level, and the high level should be put to the specified position.

♦ Check if the V-belt is tight.

♦ The impeller should be turned flexibly without friction noise.

♦ Check whether each fastener is loose and whether there is leakage in each sealing part.

♦ Turn on the main motor of the disperser and check whether the rotation direction of the stirring is the same as the direction specified by the equipment.

♦ Make sure the above inspection work is correct before driving.

Drive

♦ Place the impeller in the center of the container of the disperser, press the down button, and lower it to the low position or the required position.

♦ Both handles must be locked before driving.

♦ Turn on the main motor and press the button according to the speed required for operation.

♦ Pay attention to the current during operation. If overload operation is found, stop the machine to check the cause, and then continue to operate the disperser after taking measures.

parking

♦ Stop the main motor first to stop all the impellers.

♦ Turn on the disperser up button to raise the main shaft impeller above the container and clean the impeller.

Power conditions:

♦ Power supply voltage fluctuations usually use% 10% and -15% for AC, and DC allowance of ±% 10.

♦ The rated current and power consumption should be selected according to the power supply capacity. It should be noted that the VA value is higher at the start of AC, and indirect guided disperser should be preferentially selected when the capacity is insufficient.

♦ According to the type of power supply, AC and DC dispersers are selected. In general, AC power is easy to access.

♦ For voltage specifications, AC380V, AC220V, and DC24V are preferred.

Fourth, the standard configuration: