1、ZJ-V5B hydraulic shaftless mill roll stand 全液压无轴纸架

ⅰ、Structural features结构特点：

★Adopt hydraulic drive to complete the paper clamping, loosen, remove for the medium, translation left and right and others，the lifting of the paper adopts hydraulic drive.

采用全液压驱动来完成原纸夹紧、松开、移动对中、左右平移等动作，原纸升降采用液压驱动。

★Brake adjustable adopts multipoint braking system.

刹车调整采用多点式刹车系统。

★Each paper rack is equipped with two paper carts that can be served simultaneously from both sides.  每台纸架配两台上纸小车从两侧可同时上纸。  

ⅱ、Technical parameter技术参数：

1、Paper clip range  maximum : 1800mm     minimum : 1000mm  

夹纸范围： ： 1800mm     小：1000mm

2、Folder diameter  maximum : 1500mm     minimum : 350mm

夹纸直径： ：￠1500mm     小：￠350mm

3、Main shaft diameter of paper holder：￠240mm   纸架主轴直径：￠240mm

4、Gas source work pressure（Mpa）：0.4---0.8Mpa 气源工作压力（Mpa）：0.4---0.8Mpa    

ⅲ、 Hydraulic system parameters  液压系统参数：

1、Work pressure（Mpa）:16---18Mpa                工作压力（Mpa）:16---18Mpa  

2、Lifting hydraulic cylinder：￠100×440mm          升降液压缸：￠100×440mm   

3、Clamping hydraulic cylinder：￠63×1300m          夹紧液压缸：￠63×1300mm

4、Hydraulic station motor power：3KW --380V -- 50Hz   液压站电机功率：3KW --380V -- 50Hz    

5、Solenoid valve voltage：220V  50 Hz               电磁阀电压：220V  50 Hz

2、paper trolley、track上纸小车、导轨         

ⅰ、Structural features结构特点：

★Push the roller in place将卷筒纸推送到位。

★Track whole buried, The main frame of the 14th channel with ¢ 20mm cold drawn  round  welding，the track length 6000mm。

轨道整体埋地，主架为14号槽钢与￠20mm冷拔圆钢焊接，地轨长度6000mm。

★Each paper with two stage paper trolley,and the paper from the two sides at the same time。每台纸架配两台上纸小车从两侧可同时上纸。

3、Automatic paper picking machine

150-1800型全自动接纸机

ⅰ、Structural features结构特点：

★Maximum diameter of base paper：1500mm。适用 原纸直径：1500mm。

★Mill roll stand with automatic tension control, high-speed paper receiving success rate.

配合原纸架自动张力控制，可高速接纸，成功率高。

★Paperless tail then the paper, to reduce the paper loss(Paper tape and only partially overlap with a width of 40mm.)

无纸尾接纸，降低原纸损耗（原纸重叠部分只与胶带同宽约40mm）。

★When the paper car out, automatic transfer out,and the vacuum suction,easy paper loading, automatic tension control,zero error of paper receiving.

接纸车移出时，自动转出，装纸容易，全自动张力控制接纸零失误。

★all PLC automatic control,accurate,less failure,easy maintenance.

全部采用PLC自动控制，动作准确，故障少，维护方便。

★The first buffer wheel pull the paper, automatic alignment, easy to pull paper.

缓冲轮 次拉纸时，自动对齐，容易拉纸。

★Machine superiority, cylinder control of the paper machine at high speed, the paper will not appear in the ordinary motor control of broken tiles, foaming phenomenon.

机器优越性，气缸控制的接纸机高速接纸瞬间不会出现普通电机控制的碎瓦、起泡现象。

★Maximum paper speed 150 m / min.

高接紙速度150米／分。

ⅱ、Technical parameter技术参数：

1、Effective width：1800mm               工作幅宽：2200mm                  

2、Operation direction：left or right（determined in accordance with customer plant）

操作方向：左置或右置（根据客户厂房确定）

3、Design speed：150m/min              机械速度：150m/min               

4、Working speed：0-150m/min           运行速度：0-200m/min

5、Pressure：6bpa                      压力：6bpa        

6、Single machine weight：max 2300Kg   单机重量： 2300Kg

ⅲ、Roller diameter parameter辊类直径参数：

1、Up guide paper shaft：￠126mm                 上导纸轴： ￠126mm             

2、Down guide paper guide： ￠126mm             下导纸轴：￠126mm    

3、Buffer roller guide roller1： ￠118mm             缓冲辘导辊1： ￠118mm             

4、Buffer roller guide roller2：￠126mm              缓冲辘导辊2： ￠126mm           

5、Paper pinch roll： ￠99mm                      夹纸辊：￠99mm             

6、Paper roll：￠99mm                            托纸辊：￠99mm

4、RG-1-900 top（core）paper preheater   RG-3-900 three preheater

R09B面（芯）纸预热器 、RG-3-900三重预热器

ⅰ、Structural features结构特点：

★The preheating roller is designed with butterfly head, which conforms to the first class national standard of pressure vessel and has the certificate of pressure vessel.

预热辊采用蝶型封头设计，符合一类压力容器国家标准，并附有压力容器证书。

★The roll surface after precision grinding, fine grinding and hard chromium plating processing，surface friction is small and durable。

各辊表面经精密磨削后精磨并镀硬铬处理，表面摩擦力小，耐用。

★Electric adjustment wrap angle , wrap angle can be rotated within 360 °to adjust the paper heat area . 电动调整包角，包角可在360°范围内旋转调节纸张受热面积。

ⅱ、Technical parameter技术参数：

★Effective width：1800mm                       工作幅宽：1800mm

★Diameter of the preheat roller：￠900mm         预热辊直径：￠900mm     

★Diameter of the angle：￠110mm×2             包角轴直径：￠110mm×2

★Steam temperature：150-200 ℃                蒸汽温度：150-200℃       

★Steam pressure：0.8-1.3Mpa                   蒸汽压力：0.8-1.3Mpa

★Motor power：250W  short（S2）work system   电机功率：250W    短时（S2）工作制

4、SF-320C fingerless type single facer  SF-320C吸附式单面机   

ⅰ、Structural features结构特点：

★Adopt hood suction structure，matched high pressure powerful fan. Gas supply and electrical control cabinet to focus on the same operation, the operating side full cover closed.

采用罩吸式结构，配高压强力风机。气源及电气控制集中于同一操作柜，操作侧全封闭全罩。

★High quality resin sand casting，wall thickness 200mm。Adopt independent gear box, Universal joint transmission structure.

优质树脂砂铸件，墙板厚度200mm。采用独立变速箱，万向节传动结构。

★install the lifting trolley on the conveyor bridge,Need to use the car will tile roll assembly and pressure roller, such as convenient and quick.

在输送天桥上面加装了吊装小车，需要时利用该车将瓦辊总成及压力辊等取出，方便快捷。

★Glue roller unit structure with the overall relocation，Maintenance can sway the machine at the overall maintenance，improve the working efficiency。

涂胶辊单元采用整体外移式结构，维护时可整体侧移出机处进行维护，提高了工作效率。

★The humidity control apparatus equipped with a spray, so flute type to maintain good stability of deformation, avoid dry。

配用喷雾调湿装置，使瓦楞楞型保持良好的变形稳定性，避免干裂。

★Automatic circulation system for glue, two-cylinder pneumatic gluing device, with good cushioning effect.

采用自动循环式供胶系统，双气缸气动上胶装置，具有良好的缓冲效果。

★Glue department using integrated slide structure，Glue roller surface after grinding engraved with 32 lines and pit-style textured hard chrome plating.

涂胶部采用整体式滑板结构，涂胶辊表面经精磨后刻有32线凹坑式网纹并镀硬铬处理。

★Corrugated roller adopt tungsten carbide dealing，diameter of the main corrugated roller¢ 320mm，Quenched→rough car→bore fine boring→shaft head shrunk-on→welding → tempering to stress→fine cars→coarse grinding→IF quenching→CNC grinding machine grinding→tungsten carbide dealing，hardness of surface is HV58degrees。

瓦楞辊材质48CrMo合金钢，瓦楞主辊直径¢ 320mm，经调质→粗车→内孔精镗→轴头烘装→焊接 → 回火去应力→精车→粗磨→中频淬火→数控磨床精磨→碳化钨处理。

★Active force variable frequency motor drive, energy efficient, low failure rate。

主动力采用变频电机驱动，节能 ，故障率低。

★Glue wide electric adjust to changes in the width of the paper used。

涂胶宽幅电动调整，以适应所用原纸宽度变化。

★Amount of glue size with electric adjustment, touch screen display and operation of the encoder transmission coating gap, high accuracy。

涂胶量大小采用电动调整，触摸屏显示及操作，通过编码器传输涂胶间隙，精确度高。

★Power and operating parts with a safety net to ensure the safety of personnel in the operation of machinery。

动力及操作部位配有安全防护网，以确保人员在机器运转时的安全。

ⅱ、Technical parameter技术参数：

★Effective width：1800mm                工作幅宽：1800mm                  

★Operation direction：left or right（determined in accordance with customer plant）

操作方向：左置或右置（根据客户厂房确定）

★Design speed：150m/min                设计速度：150m/min              

★Temperature range：160—180℃         温度范围：160—180℃

★Corrugated flute:（UV type or UVV type） 瓦楞楞型（UV型或UVV型）：

ⅲ、Roller diameter parameter辊类直径参数：

★Corrugated roll diameter瓦楞辊直径： up￠313mm      down￠316mm   

★Pressure roll diameter压力辊直径： ￠320mm

★Glue roller diameter涂胶辊直径： ￠240mm        

★ Fixed paste roller定糊辊： ￠140mm   

★Preheater diameter预热器直径： ￠402mm

ⅳ、Powered motor parameters动力电机参数：

★Main frequency drive motor：18.5KW     主变频驱动电机：18.5KW

★Suction motor：11KW                   吸风电机:11KW         

★Glue reducer：100W                    调胶减速机：100W   

★Glue adjusting  motor：200W*2          隔胶调整电机：200W *2 

★Glue pump motor：2.2KW               胶泵电机：2.2KW

5、ZDF conveyor bridge  输送过桥                                     

ⅰ、Structural features结构特点：

★This part is the main beam of the 20th channel, 16-beam, angle iron 63, column, etc. are connected.

本部分是主梁为20号槽钢、16号工字钢、63号角钢、立柱等连接而成。

★Both sides of the security fence, ladder , high-strength save people the word pedals, ensure the safety of personnel and easy to operate.

两侧均有安全护栏、梯子（用8号小槽钢制作）、高强度人字踏板，确保人员的工作安全以及操作方便。

★Pull the paper shaft surface tension axis, feeding shaft by grinding hard chrome plated.

牵纸轴、张紧轴、输纸轴等表面经磨削加工镀硬铬处理。

★Vacuum tension control, 5-inch suction tube, plus regulating valves, air flow can be infinitely adjustable.

真空吸附张力控制，吸风管5寸，加调节阀门，风量可无级可调。

★Dual front bezel correction guide column positioning, screw driver, fast and accurate positioning, walking steadily.

纠偏挡板前采用双导向柱定位，丝杠驱动，定位快速准确，行走平稳。

ⅱ、Roller diameter parameter辊类直径参数：

★Paper roll and a tension roller diameter:￠130mm         上纸辊及张紧辊直径：￠130mm      

★Conveying roller diameter：￠180mm                    输送辊直径：￠180mm

★Active tension roller diameter：￠85mm                  主动张紧辊直径：￠85mm      

★Diameter of over paper rollers and guide rollers：￠110mm 过纸辊及导纸辊直径：￠110mm

★Paper towing shaft diameter：￠110mm                  上纸拖带轴直径：￠110mm       

ⅲ、Powered motor parameters动力电机参数

★Corrugated single paper lift motor：2.2KW                单面瓦楞纸提升电机：2.2KW

★The bridge adsorption motor：2.2KW                     过桥吸附风机：2.2KW       

★Wide motor tune cardboard：250W                      调纸板宽幅电机：250W       

6、GM-20  Double glue machine二层涂胶机 

ⅰ、Structural features结构特点：

★After the surface of cots is adjusted and tempered, the inner hole is processed, the dynamic balance surface is polished and there are 32 lines of concave net pattern, the glue is uniform and the amount of glue consumption is less.

涂胶辊表面经调质后，内孔加工，做动平衡表面精磨并刻有32线凹坑式网纹，涂胶均匀，耗胶量少。

★The rotation of the cots is controlled by the variable frequency motor and frequency conversion, and the frequency control ensures that the linear speed of the cots is synchronized with the two sides, and it can operate independently.

涂胶辊的转动由变频电机加变频控制，由变频控制保证涂胶辊的线速度与双面机同步，又可以独立运转。

★Coating electric adjustment glue amount of digital display. Automatic circulation of glue, can effectively control the amount of glue, avoid glue precipitation, ensure good glue and save glue.涂胶电动调整胶量数显。自动循环供胶，能有效控制胶量，避免胶水沉淀，保证良好的胶水和节约胶水。

★All roller surfaces are ground after hard chromium plating.

所有辊轴表面均经过磨削处理后镀硬铬。

★ The speed signal of double-sided machine is measured to realize synchronous operation with it. The rubber coating machine is displayed with man-machine interface, which can be used for data setting and easy to operate.

测取双面机速度信号，以实现与其同步运转。涂胶机采用人机界面显示，可进行相关数据设定，操作简便快捷。

★Electrical design, construction production process, follow the national standards, low failure rate, easy maintenance。

电器设计、生产施工工艺，遵循国家标准规范，故障率低，维护简单。

ⅱ、Technical parameter技术参数：

★Effective width：1800mm                         工作幅宽：1800mm           

★Operation direction：left or right（determined in accordance with customer plant）

操作方向：左置或右置（根据客户厂房确定）

★Design speed：150m/min                        设计速度：150m/min

★Gas supply system：0.4—0.6Mpa                 气源系统：0.4—0.6Mpa

★Preheat cylinder temperature range：150—200℃   预热缸温度范围：150—200℃     

★Steam pressure:0.8—1.2Mpa                     蒸汽压力：1.12—1.3Mpa

ⅲ、Roller diameter parameter辊类直径参数：

★Glue roller diameter：￠269mm                   涂胶辊直径：￠269mm               

★Doctor roller diameter：￠142mm                 定糊辊直径：￠142mm

★Over the paper roll diameter：￠110mm            过纸辊直径：￠110mm

ⅳ、Powered motor parameters动力电机参数：

★Glue roller initiative frequency motor：3KW         涂胶辊主动电机：    3KW            

★Sizing Reducer:：250W                          胶量调整减速机：    250W          

★Pressure roller clearance adjustment motor： 250W 压力辊间隙调整电机：  250W          

★Glue pump motor：2.2KW                        胶泵电机：2.2KW           

7、SM-F type double facer双面机    

ⅰ、Structural features结构特点：

★The surface of the heating plate is grinded, the width of the hot plate is 600mm, there are 16 heating plates, the cooling setting is 4 meters.The heating plate is made of vessel plate, which conforms to the national first-class pressure vessel standard, with pressure vessel certificate and inspection certificate.

加热板表面经研磨处理，热板宽度600mm，共16块加热板，冷却定型部长4米。加热板采用容器板制作，符合国家一类压力容器标准，附有压力容器证书及检验合格证。

★The upper conveyer belt rectifies the right and left side to adopt the pneumatic automatic correction deviation.

上输送带左右纠偏调整采用气动自动纠偏。

★Heating plate heat transfer pipe temperature control sub-four-segment, with a temperature display.  加热板的导热配管分四段控制温度，设有温度显示。

★Double cylinder S type cotton belt tensioning device is used for upper cotton belt.

上棉织带采用双气缸S型棉织带张紧装置。

★The lower belt adopts pneumatic tension, pneumatic correction.下带采用气动张紧，气动纠偏。

★Drive roller coated with attached wear-resistant rubber ，showed a herringbone structure，With a high, ensure smooth cardboard output。

驱动辊表面包附耐磨像胶，呈人字型结构，并带有中高，保证纸板平整输出。

★Main drive motor for frequency conversion motor，low-speed torque，wide speed range ,reliable, and easy maintenance.

主驱动电机为变频调速电机，低速力矩大，调速范围广，使用可靠，维护简单。

★Hot plate internal for partition isolation structure,s-shaped flow of steam，Steam, water separation function significantly improves the utilization of steam。

热板内部为隔板隔离结构，使蒸汽呈S形流向，汽、水分离功能明显，提高了蒸汽利用率。

ⅱ、Technical parameter技术参数：

★Temperature requirement：160—200℃                  温度要求：160—200℃   

★Steam pressure：0.8-1.3MPa                           蒸汽压力：0.8-1.3MPa        

★Air source pressure：0.6—0.9MPa                      气源压力：0.6—0.9MPa 

★Cooling stereotypes length：4m                         冷却定型长度：4米      

★Heating plate quantity：16 pieces                       加热板数量：16块            

ⅲ、Roller diameter parameter辊类直径参数：

★Upper drive rubber roller diameter：￠700mm            上驱动胶辊直径：￠700mm          

★Lower drive rubber roller diameter ：￠400mm           下驱动胶辊直径：￠400mm       

★Former follower with roller diameter：￠215mm           前从动带辊直径：￠215mm          

★Back setting belt driven roller diameter：￠215mm        后定型从动带辊直径：￠215mm

★Platen roller：￠70mm                                 压带辊直径：￠70mm           

★Setting roller diameter：￠86mm                        定型托辊直径：￠86mm

★Upper belt tension roller diameter：￠155mm             上带张紧辊直径：￠155mm         

★Upper roll diameter with detuning：￠130mm             上带调偏辊直径：￠130mm

★Entrusted with the roll diameter lower belt：￠130mm      下带托带辊直径：￠130mm

★Lower belt tension roll diameter: ￠130mm                下带张紧辊直径：￠130mm  

Note: All the roller surface after grinding are hard chrome plated。

注：所有辊轴表面均为磨削后镀硬铬处理。

ⅳ、Powered motor parameters动力电机参数：

★Main drive motor power：30Kw                          主驱动电机功率：30KW         

8、NCBD thin blade slitter scorer（Zero Pressure Line）

NC电脑薄刀纵切压痕机（零压线型 ） 

ⅰ、Structural features结构特点：

★Synchronous servo motor control row of knives, cable. Automatic reset. Precise dimensions.change order time 3-8 seconds,the two machines can be achieved with no slow down immediately for a single memory of 999 order,non-stop automatic change order or manual change order can be realized.

同步伺服马达控制排刀，排线。自动复位。精准尺寸。换单时间3-8秒。两机并用可实现不降速立即换单。存储999组定单，实现不停机自动换单或手动换单。

★Schneider M258PLC control system, using CANopen line system, with order management capabilities, with the dryer speed synchronous signal input.

施耐德 M258PLC 控制系统，采用CANopen 总线系统，具备定单管理功能，配有与烘干机速度同步信号输入接口。

★HMI with 10.4-inch color touch screen, storage 999 orders, change orders automatically or manually for a single, fault alarm.

人机界面采用10.4寸彩色触摸屏，存储999组定单，实现自动换单或手动换单，故障自动报警。

★Three kinds of pressure line forms：Convex against the concave（three layers line）、Convex against the concave（five layers line）、Convex against Flat，Three kinds of electric pressure line forms can be converted。Crimping round shades by computer control，linear, and easy to bend.三种压线形式：凸对凹（三层线）、凸对凹（五层线）、凸对平，三种压线形式可以电动转换。压线轮深浅可由电脑自动控制，线形好、易于折弯。

★Using thin tungsten alloy steel knife，sharp blade，long life of more than 8 million meters.

采用薄型钨钢合金刀，刀锋锋利，使用寿命大于800万长米。

★knife sharpener for computer control，automatic or manual knife sharpener，Cutting edge sharpening can be divided,improve productivity Efficiency.

磨刀为电脑控制，自动磨刀或手动磨刀，可边分切边磨刀，提高生产效率。

★Imported synchronous drive system, precision accurate, long life, low noise operation。

采用进口同步带动装置，精度准，寿命长，运行噪音低。

ⅱ、Technical parameter技术参数：

★Effective width：1800mm                         工作幅宽：1800mm             

★Design speed: 150 m / min                        设计速度：150m/min

★Operation direction：left or right（Determined in accordance with customer plant）

操作方向：左置或右置（根据客户厂房确定）

★Mechanical configuration：Zero pressure line thin blade slitter scorer 5 knives 8 lines       

机械配置：零压线型电脑薄刀纵切机5刀8线             

★Minimum cutting width: 135mm                       小切纸宽度：135mm

★Cutter wheel positioning accuracy: ±0.5mm          刀线轮定位精度: ±0.5mm  

★The minimum distance between the indentation：0mm   小压痕距离：0mm

ⅲ、Powered motor parameters动力电机参数：

★Line cutter line motor:0.4KW                       排刀线伺服电机:0.4KW    

★Knife wheel drive motor:5.5KW                    刀轮驱动电机:5.5KW   

★Wheel drive motor：5.5KW                       线轮驱动电机:5.5KW   

9、NC-150  NC cutter helical knives  电脑螺旋刀横切机   

ⅰ、Structural features结构特点：

★It can store 200 units orders，replace the cutter specifications quickly and accurately，changing orders without stop,And enables networked computers to facilitate production management.

可储存200组定单，更换切纸规格迅速准确，不停机换单，并可实现计算机联网，方便生产管理。

★Knife shaft drive gears are precision forged steel induction hardening, backlash-free transmission, advanced keyless connection, high transmission accuracy。

刀轴传动齿轮采用精锻钢材料高频淬火，实现无侧隙传动，采用先进的无键连接方式，传动精度高。

★Cutting machine adopts inlaid front steel blade knife spiral structure, serrated knife. scissors, shears, shear force, long blade life。

横切机刀片采用镶锋钢螺旋刀结构，锯齿刀型。剪刀式剪切，剪切力小，刀片寿命长。

★Around feed rollers are used  the sun gear platen way, smooth delivery, pressure evenly, easy to crush plate board or cause blockage。

前后送纸轮均采用太阳轮压纸方式，输送平稳，压力均匀，不易压坏板板或造成堵塞。

★This type of brake is energy storage type (non-energy brake), so in the process of production, the average power consumption is 1 / 3 of that of the ordinary NC cutting machine, saving more than 70% of electricity and achieving the goal of saving money.

本机型是储能式制动（非能耗制动），故在生产过程中低能耗，平均用电量是普通NC切断机的1/3，节省电70%以上，达到省钱的目标。

★Exact and adjustable no gap gear to ensure precise blade engagement, running balance.

精密可调无隙齿轮，确保刀口精确啮合，运行平衡。

★Independent oil pump and filter are used to distribute two sets of copper pipes in each gear position to feed oil, lubricate and cool.

采用独立油泵和过滤器配合两组紫铜管分布于各齿轮位供油，润滑和冷却。

★Knife roller: fine quality forged steel material, the balanced, with good stability.

刀辊：优质精锻钢材质，经平衡处理，具有良好的平稳性。

ⅱ、Technical parameter技术参数：

★Effective width：1800mm                          工作幅宽：1800mm                  

★Operation direction：left or right（determined in accordance with customer plant）

操作方向：左置或右置（根据客户厂房确定）

★Design speed: 150 m / min                         设计速度：150m/min               

★Mechanical configuration: computer helical cutter crosscutting  机械配置：电脑螺旋刀横切

★Minimum cutting length：500mm                     小切纸长度：500mm                   

★Maximum cutting length：9999mm                   切纸长度：9999mm

★Cutter accuracy: Uniform for ± 1mm,  non-uniform to ± 2mm

切纸精度：匀速为±1mm，非匀速为±2mm

★Equipment size: Lmx4.2 Wmx1.2 Hmx1.4            设备尺寸：L_mx4.2*W_mx1.2*H_mx1.4

★Single machine weight: maximum 3500kg            单机重量： 3500Kg

ⅲ、Roller diameter parameter辊类直径参数：

★Cross on the knife shaft center distance：￠216mm    横切上、下刀轴中心距：￠216mm        

★Before the lower conveying roller diameter  ￠156mm  前下输送辊直径  ￠156mm  

★After the lower conveying roller diameter：￠156mm   后下输送辊直径：      ￠156mm             

★Roll diameter: 160mm。                            牵纸辊直径：￠160mm          

★Output solar wheel diameter: 160mm                 输出太阳轮直径： ￠160mm

Note: all roller shafts after grinding, the surface of hard chromium plating (except upper, lower tool shaft).

注：所有辊轴均经磨削后，表面镀硬铬处（上、下刀轴除外）理。

ⅳ、Powered motor parameters动力电机参数：

★main drive motor power：22Kw   Full AC synchronous servo

主驱动电机功率：22KW             全交流同步伺服

★Before feeding motor power：3Kw（Frequency Control）

前后输纸电机功率：3KW（变频调速）

10、DM-XLM Automatic small gantry stacking machine

全自动龙门式堆码机 

ⅰ、Structural features结构特点： 

★Gantry stacking。Changing single time is 5seconds，automatic counting, automatic cross out automatically for a single.

龙门式堆码。换单时间5秒，可自动计数，自动横出，自动换单。

★Synchronized with the production management system，order mangement，Centralized management，do not slow down automatically for a single.

与生管系统同步，订单管理，集中管理，不降速自动换单。

★The waste of changing single tube was less than 700 mm.生管换单浪费小于700mm。

★crawler stacking platform，AC servo control movements，Stacking smooth, neat;履带式堆码平台，交流伺服控制升降，堆码平稳、整齐；

★When stacking reaches a set number of automatic frequency control smooth laterally out of paper；

堆码达到设定数量时变频控制自动平稳横向出纸；

★Tailgate AC servo control positioning for a single automatic, rapid, precise adjustment；

后挡板交流伺服控制定位，换单时自动、快速、精确调整；

★Tailgate automatically shift for small orders stacking；

后挡板可自动移位，适合小订单堆码；

★Delivery side of the standard electric transport planes, and duplex trolley。

输送侧标配电动输送架，及双工位台车。

★Independent sealed control cabinets, electrical equipment operating under clean environment；

独立密封控制柜，电气设备在无尘、环境下运行；

★Color touch-screen display for easy on-site operation。

彩色触摸屏显示，方便现场操作。

★Fully automatic operation control, improve efficiency and save manpower, reduce labor intensity；全自动运行控制，提 率，节省人力，降低操作人员劳动强度；

ⅱ、Technical parameter技术参数：

1、Effective width：1800mm                   工作宽幅：1800mm            

2、Operation direction：left or right（determined in accordance with customer plant）

操作方向：左置或右置（根据客户厂房确定）

4、Working speed: 150m / min                工作速度：150m/min             

4、Maximum stacking height: 250mm           堆积高度：250mm

5、Maximum stacking length: 3500mm          堆积长度：3500 mm