- 产品
- 详情
- 推荐
收藏
¥ 15870.00
1套起订
产品规格
可售数量： 1000套
电动破碎设备
块料破碎阀Block crushing valve
The main function of the block crusher is to crush the blocks in the material flow of the unloader. These blocks are formed by moisture in the warehouse or warehouse.
Because the lump material in the material cannot pass through the discharge port of the discharger, it will cause material blockage and cause the flow control valve to generate false information of untrue flow. In light cases, it will affect the normal production of the process system, and in serious cases, it will cause serious imbalance between raw materials and fuel due to false signals, resulting in temperature rise in the combustion equipment and equipment accidents.
The block crusher can be installed horizontally or vertically at the discharge outlet, such as the front of the flow regulating valve or pneumatic shut-off valve. When a large piece of material appears, it can be broken immediately to prevent the large piece of material from blocking the channel of the discharge valve.
A radially arranged crushing claw is installed on the rotor of the crusher to move the block material through the grid and crush it.
The operation safety of the block crushing valve is guaranteed by the motor speed detection device integrated in the electric control box. When some block materials in the materials cannot be broken and jam the rotor, the speed detection device will alarm and automatically reverse, and push away the block materials that cannot be broken before forward rotation.
When the block material is too hard to be broken, the crusher will repeat forward and reverse rotation and alarm continuously. After the alarm, the operator shall remove these unbreakable blocks as soon as possible to avoid long-term forward and reverse rotation, resulting in equipment damage.
When the forward or reverse rotation is stuck, the crusher will stop automatically and wait for troubleshooting before operation.
The speed detection device is an optional device, which needs to be emphasized when ordering.
Characteristics of block crusher
• the flow of large models can reach 1000m3 / h
• suitable for all kinds of gasification chute and storage unloading outlet
• designed for material temperatures up to 120 degrees
• low energy consumption, only the driving motor power is 1.1KW (specifications below B400) and 1.5KW (specifications above B500) at 25 revolutions
• crushing claws and grid plates are made of high wear-resistant materials
• simple operation and maintenance
• integrated speed detection device (optional)
• when the integrated speed detection device is selected, it is equipped with an electric cabinet
块料破碎器的主要的功能是破碎卸料器物料流中的块料，这些块料是物料在库内或仓中因受潮而形成。
物料中的块料由于通过不了卸料器的卸料口，因此会造成物料堵塞并引起流量调节阀产生非真实流量的虚假讯息，轻者影响工艺系统的正常生产，重者则会因为虚假信号造成原料和燃料之间的比例严重失调，从而造成燃烧设备中温度上升，导致设备事故。
块料破碎器可水平安装也可垂直安装在卸料出口处卸料设备的入料端口，如流量调节阀或气动切断阀的前部。当物料中出现较大块状物时，可即刻将其破碎，以防止大块物料堵塞卸料阀门的通道。
破碎器的转子上安装放射状布置的破碎爪，拨动块状物料通过栅格并将其破碎。
块料破碎阀的运转安全性是通过在电控箱中集成的电机转速检测装置来保证，当物料中的某些块状物料无法破碎而卡住转子时，转速检测装置将报警并自动反转，将无法破碎的块状物料推开后再进行正转。
当块状物料过于坚硬而无法破碎时，破碎器则会如此反复地正反转并持续地报警。报警后操作员工应尽快将这些无法破碎的块料清除，以免长期的正反转从而导致设备损坏。
当正转或反转都被卡住时，破碎器会自动停机，等待排除故障后再运行。
转速检测装置为选配装置，有此要求时需要在订货时强调说明。
块料破碎机的特点
•大型号的通过流量可达1000m3/h
•适用于各种气化斜槽和储库卸料出口
•为高达120度的物料温度而设计
•低能耗，在25转时仅为驱动电机功率为1.1KW（B400以下的规格）和1.5KW（B500以上规格）
•破碎爪和栅格板使用高耐磨材料
•操作及维护简单
•集成转速检测装置（选配项）
•选配集成转速检测装置时，随机配带电控箱
瑞文电子式套筒调节阀 电动单座调节阀 T940H-10C自力式温度调节阀
¥1450.00
瑞文DQF 4s快开球阀 DQF32 40 80 100 150电动球阀 水泥均化库专用
¥1000.00
瑞文电动气动风门dn1250 圆式窗式电动风量调节阀 涡轮通风蝶阀dn1300
¥3000.00
江苏瑞文新气动库底散装卸料阀CP300气动流量调节阀B400 气动开关阀CP350 斜槽专用气动弧形阀b500
¥3490.00
瑞文双轴电动物料凝结电动破碎机 PSF500 块料碎渣机 PSF400 水泥粉煤灰结团打散破碎阀PSF300
¥11000.00
瑞文新粉碎机 电动块料破碎阀psf500 物料凝结湿泥块破碎阀PKD400
¥9999.00
瑞文新破碎阀PKD500 电动块料破碎器600*600 800*800-斜槽水泥块料PSF破碎阀B315 电动破碎设备
¥ 15870.00
¥15870.00
1000套可售
询价单发送成功～