【以色列Ophir激光功率计（不含水冷系统）型号:10K-W-BB-45库号：M347838】价格_批发_厂家_参数_图片_其他专用仪器仪表

1/1

以色列Ophir激光功率计（不含水冷系统）型号:10K-W-BB-45库号：M347838

¥ 79500.00

1台起订

产品规格

可售数量： 410台

北京中西华大科技有限公司

采通通 4 年资质认证实名企业

5年

经营年限

北京

所在地区

9.9

综合评分

全部产品进入店铺

图文详情

产品属性

以色列Ophir激光功率计（不含水冷系统）型号:10K-W-BB-45库号：M347838 以色列Ophir激光功率计以色列OPHIR公司成立于1976年，拥有30多年的激光功率能量量测设备的和经验。其产品种类齐全;测试准确、使用方便，被应用于科研、工业和医疗等各个领域。2006年，OPHIR公司收购了美国SPIRICON公司，大大加强了其激光光斑／光束质量分析产品线，成为了上大的激光量测设备的供应商。完全符合以下参数要求主要测试激光器的参数如下：平均功率范围：3kW-5kW 波长：1080nm 脉宽：连续重复频率：无入射光斑大小：5-10mm 同时，希望兼容以下激光器参数：平均功率范围：500W 波长：1064nm 脉宽：4-250nm 重复频率：20-2000kHz 入射光斑大小：5-10mm 重量4.5kg左右具体参数如下： Features • Very high powers • Water cooled • Up to 11kW • Up to Ø45mm apertures Model 10K-W-BB-45 Use High power up to 11kW Absorber Type Beam deflector + broadband absorber Spectral Range µm (a) 0.8 - 2, 10.6 Aperture mm Ø45mm Power Range 100W – 11kW Power Scales 11kW / 6kW / 600W Power Noise Level 1W Backscattered Power (b, e) ~3.5% without Scatter Shield, ~1% with Scatter Shield Maximum Average Power Density kW/cm 2 See note (c) and table (1) below Response Time with Meter (0-95%) typ. s 2.7 Calibration Uncertainty ±% 1.9 Power Accuracy ±% 5 (a) Linearity with Power ±% 2 Cooling water (d) Minimum Water Flow Rate 8 liter/min at full power (d) Water Connectors (e) Quick connector for 3/8” OD nylon tubing Cable Length 5 meters Optional Scatter Shield Accessory (e) 10K-W / 15K-W Scatter Shield (P/N 7Z08295) Weight kg 4.5 Compliance CE, UKCA, China RoHS Version V4 Part number 7Z07102 Notes: (a) Calibrated at 1.07μm and 10.6μm. For other wavelengths in the range 0.8 – 2μm add up to ±2% to the calibration error. Notes: (b) When scatter shield is installed, use the NIRS setting to compensate for slightly higher reading. When not installed, use the NIR setting. Notes: (c) For circular beam centered within ¼ of beam diameter. IMPROPERLY CENTERED BEAM CAN CAUSE DAMAGE TO SENSOR. Maximum tilt angle ±5 degrees. For rectangular beam please consult Ophir representative. Notes: (d) Water temperature range 18-30ºC. Water temperature rate of change <1ºC/min. Pressure drop across sensor 0.1MPa. The recommended flow rate can be lowered proportionately at lower than full power but should not be below 3 liter/min. The response time will be optimum with the recommended flow rate. For solutions for prolonged usage with untreated water (tap water, non DI water), please contact Ophir. Notes: (e) Heavy duty stand is available as optional extra. For further information and other options see Accessories for High Power Sensors on pages 82-86. Table: (1) Beam diameter Max power density Max energy density 1ms pulse width 3ms pulse width 10ms pulse width <15mm 10kW/cm 2 30J/cm 2 60J/cm 2 150J/cm 2 15 - 20mm 7kW/cm 2 20J/cm 2 40J/cm 2 100J/cm 2 20 - 40mm 5kW/cm 2 15J/cm 2 30J/cm 2 70J/cm 2 40 - 45mm 4kW/cm 2 12J/cm 2 25J/cm 2 60J/cm